sinon j’ai quand meme essayé de compiler le pilote dans usr/src/webcam/ apres dans son terminal en mode su j’ai tapé make (ou make all) et voici l’erreur
[xerxesis@localhost ov51x-1.65-1.12-mark]$ make
make -C /lib/modules/2.6.12-12mdk/build M=/usr/src/webcam/ov51x-1.65-1.12-mark modules
make: *** /lib/modules/2.6.12-12mdk/build: Aucun fichier ou répertoire de ce type. Arrêt.
make: *** [all] Erreur 2
[xerxesis@localhost ov51x-1.65-1.12-mark]$
est ce que ça te dis quelquechose stp?
tu ne doit pas prendre les sources du kernel sur kernel.org
ce site contient les sources “officielles” non configurées du kernel (aussi appellées “vanilla”)
ta distribution (comme toutes les autres) peut parfois “patcher” le kernel qu’elle utilise pour se simplifier l’utilisation de logiciels (automount il fut un temps) ou pour corriger de petits bug sans changer completement de version.
du coup, tu trouveras les sources de ton kernel avec urpmi (si tu es bien sous mandriva) comme tous les logiciels que tu dois instaler !
pour ton erreur, c’est normal. normalement, le dossier “/lib/modules/2.6.12-12mdk/build” est un raccourci vers les sources du kernel 2.6.12-12mdk, et comme elles ne sont pas installée, il n’a pas pu les trouver, d’où l’erreur “Aucun fichier ou répertoire de ce type” 
dorénavant je suis sous kubuntu vu que quasiment tout le monde l’utilise je me suis dis que pour apprend c’était peut etre beaucoup mieux
donc tu m’a dis qu’il ne fallait surtout pas installé le kernel sous leur site officiel donc vu que maintenant je suis sous kubuntu que dois-je faire (mon noyau est le 2.6.12-9-386)
et encore merci de votre patience
cordialement
sudo apt-get install linux-headers-2.6-386
cela devrait t’installer au passage le paquet : linux-headers-2.6.12-9-386
ensuite, reprends l’install de ton driver comme décrit plus haut. (n’oublie pas d’installer make et gcc, “sudo apt-get install make gcc”)
c’est vraiment bizarre j’ai fait exactement ce que tu m’as dit il n’y a meme pas eu derreur mais kopete ne la trouve pas la je t’avouerais que je suis bien pommé est ce que vous avez une petite idée?
cordialement
ps: est ce que vous avez de bonne sources pour ce fichier avec KDE 3.5.2 SVP
c’est embetant ça !
Est ce que tu as un autre logicel avec lequel tu peux vérifier que tout marche bien ?
Je n’ai pas de webcam, donc je ne peux pas beaucoup t’aider là dessus, mais konqueror devrait savoir gerer les webcam grace au protocol camera (dans la barre d’adresse, tape “camera:/”)
pour ce qui est de kopete, il te faut au moins la version 0.11, livrée avec kde 3.5. Tu peux ensuite configurer la webcam à partir de la fenetre principale de kopete (celle où il y a les contacts) menu configuration -> configurer -> peripheriques (je suis sous la 0.12, c’est peut-être un peu différent avec la 0.11)
Peux-tu aussi nous donner les infos suivantes :
Decharge et recharge le driver (modprobe -r <nom_du_driver> puis modprobe <nom_du_driver>) tapes dmesg et copie nous les dernières lignes. (si des lignes s’affichent dans le terminal, copie les aussi)
Ensuite, débranche et rebranche ta webcam, attend 5 secondes, tapes “dmesg” dans un terminal et copie nous les dernières lignes.
en fait je suis en trian de me demander si il fallait compiler ou pas le path linux-headers-2.6.12-9-386 parce que je l’ai pas fait j’avais compris qu’il fallait passer directement a l’étape 2 et 3 (qui ce sont tres bien dérouler d’ailleur)
alors ma question est juste est ce qu’il faut compiler le patch du noyau ou pas?
en tout cas merci beaucoup de me consacrer autant de temps c’est vraiment tres tres gentil
cordialement
XerXeSis
linux-headers-2.6.12-9-386
non, il n’y a rien à compiler DANS les sources du kernel. il a juste besoin que les fichiers soient copiés au bon endroit, ce qui est le cas car tu as installé le paquet.
pour les autres conseils que je t’ai donné, ou en es tu ?
bon c’est cool alors je dirais meme nikel 
demain j’essaye de faire tout ce que tu m’a dit (ce soir je ne peut pas me servir de mon pc) mais dans tous les cas merci pour tout
cordialement
XerXeSis
xerxesis@ubuntu:~/drivers/ov511-2.31$ make
Building OVCam drivers for 2.6 kernel.
make -C /lib/modules/2.6.12-10-386/build SUBDIRS=/home/xerxesis/drivers/ov511-2.31 modules
make[1]: entrant dans le répertoire « /usr/src/linux-headers-2.6.12-10-386 »
CC [M] /home/xerxesis/drivers/ov511-2.31/ov511_core.o
CC [M] /home/xerxesis/drivers/ov511-2.31/ov511_decomp.o
CC [M] /home/xerxesis/drivers/ov511-2.31/ov518_decomp.o
CC [M] /home/xerxesis/drivers/ov511-2.31/ovcamchip_core.o
CC [M] /home/xerxesis/drivers/ov511-2.31/ov6x20.o
CC [M] /home/xerxesis/drivers/ov511-2.31/ov6x30.o
CC [M] /home/xerxesis/drivers/ov511-2.31/ov7x10.o
CC [M] /home/xerxesis/drivers/ov511-2.31/ov7x20.o
CC [M] /home/xerxesis/drivers/ov511-2.31/ov76be.o
LD [M] /home/xerxesis/drivers/ov511-2.31/ovcamchip.o
LD [M] /home/xerxesis/drivers/ov511-2.31/ov511.o
CC [M] /home/xerxesis/drivers/ov511-2.31/ovfx2.o
CC [M] /home/xerxesis/drivers/ov511-2.31/saa7111-new.o
CC [M] /home/xerxesis/drivers/ov511-2.31/tda7313.o
Building modules, stage 2.
MODPOST
CC /home/xerxesis/drivers/ov511-2.31/ov511.mod.o
LD [M] /home/xerxesis/drivers/ov511-2.31/ov511.ko
CC /home/xerxesis/drivers/ov511-2.31/ovcamchip.mod.o
LD [M] /home/xerxesis/drivers/ov511-2.31/ovcamchip.ko
CC /home/xerxesis/drivers/ov511-2.31/ovfx2.mod.o
LD [M] /home/xerxesis/drivers/ov511-2.31/ovfx2.ko
CC /home/xerxesis/drivers/ov511-2.31/saa7111-new.mod.o
LD [M] /home/xerxesis/drivers/ov511-2.31/saa7111-new.ko
CC /home/xerxesis/drivers/ov511-2.31/tda7313.mod.o
LD [M] /home/xerxesis/drivers/ov511-2.31/tda7313.ko
make[1]: quittant le répertoire « /usr/src/linux-headers-2.6.12-10-386 »[QUOTE]
[CODE]xerxesis@ubuntu:~/drivers/ov511-2.31$ sudo make install Password: ./do_install.sh *.ko
Detected 2.6 kernel
Creating install path: /lib/modules/2.6.12-10-386/kernel/drivers/usb/media/
Installing ov511.ko to /lib/modules/2.6.12-10-386/kernel/drivers/usb/media/
Installing ovcamchip.ko to /lib/modules/2.6.12-10-386/kernel/drivers/usb/media/
Installing ovfx2.ko to /lib/modules/2.6.12-10-386/kernel/drivers/usb/media/
Installing saa7111-new.ko to /lib/modules/2.6.12-10-386/kernel/drivers/usb/media/
Installing tda7313.ko to /lib/modules/2.6.12-10-386/kernel/drivers/usb/media/
Finding module dependencies
All done!
xerxesis@ubuntu:~/drivers/ov511-2.31$
xerxesis@ubuntu:~/drivers/ov511-2.31$ sudo depmod
xerxesis@ubuntu:~/drivers/ov511-2.31$
xerxesis@ubuntu:~/drivers/ov511-2.31$ sudo modprobe ov511
xerxesis@ubuntu:~/drivers/ov511-2.31$
je ne me sert plus de konqueror car je suis sous ubuntu (bah finalement je le trouve meilleur que kubuntu
xerxesis@ubuntu:~/drivers/ov511-2.31$ sudo depmod
xerxesis@ubuntu:~/drivers/ov511-2.31$ sudo modprobe ov511
xerxesis@ubuntu:~/drivers/ov511-2.31$ sudo modprobe -r ov511
xerxesis@ubuntu:~/drivers/ov511-2.31$ sudo modprobe ov511
xerxesis@ubuntu:~/drivers/ov511-2.31$ dmesg
MER: vector=0x31 pin1=2 pin2=-1
[4294670.649000] NET: Registered protocol family 16
[4294670.649000] EISA bus registered
[4294670.649000] ACPI: bus type pci registered
[4294670.651000] PCI: PCI BIOS revision 2.10 entry at 0xf1e50, last bus=2
[4294670.651000] PCI: Using configuration type 1
[4294670.651000] mtrr: v2.0 (20020519)
[4294670.651000] ACPI: Subsystem revision 20050729
[4294670.658000] ACPI: Interpreter enabled
[4294670.658000] ACPI: Using IOAPIC for interrupt routing
[4294670.659000] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
[4294670.660000] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[4294670.660000] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[4294670.660000] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[4294670.660000] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
[4294670.661000] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
[4294670.661000] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
[4294670.661000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
[4294670.661000] ACPI: PCI Root Bridge [PCI0] (0000:00)
[4294670.661000] PCI: Probing PCI hardware (bus 00)
[4294670.662000] ACPI: Assume root bridge [\_SB_.PCI0] segment is 0
[4294670.662000] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[4294670.665000] PCI: Enabled i801 SMBus device
[4294670.665000] PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
[4294670.665000] Boot video device is 0000:01:00.0
[4294670.666000] PCI: Transparent bridge - 0000:00:1e.0
[4294670.667000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[4294670.667000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
[4294670.668000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI2._PRT]
[4294670.674000] Linux Plug and Play Support v0.97 (c) Adam Belay
[4294670.674000] pnp: PnP ACPI init
[4294670.680000] pnp: PnP ACPI: found 14 devices
[4294670.680000] PnPBIOS: Disabled by ACPI PNP
[4294670.680000] PCI: Using ACPI for IRQ routing
[4294670.680000] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[4294670.689000] pnp: 00:01: ioport range 0xe400-0xe47f could not be reserved
[4294670.689000] pnp: 00:01: ioport range 0xe800-0xe81f has been reserved
[4294670.689000] pnp: 00:01: ioport range 0xec00-0xec3f has been reserved
[4294670.689000] pnp: 00:01: ioport range 0x4d6-0x4d6 has been reserved
[4294670.689000] pnp: 00:0d: ioport range 0x3f0-0x3f1 has been reserved
[4294670.689000] Simple Boot Flag at 0x3a set to 0x1
[4294670.690000] audit: initializing netlink socket (disabled)
[4294670.690000] audit: initialized
[4294670.690000] VFS: Disk quotas dquot_6.5.1
[4294670.690000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[4294670.690000] devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
[4294670.690000] devfs: boot_options: 0x0
[4294670.690000] Initializing Cryptographic API
[4294670.690000] isapnp: Scanning for PnP cards...
[4294671.044000] isapnp: No Plug & Play device found
[4294671.100000] PNP: No PS/2 controller found. Probing ports directly.
[4294671.105000] serio: i8042 AUX port at 0x60,0x64 irq 12
[4294671.106000] serio: i8042 KBD port at 0x60,0x64 irq 1
[4294671.106000] Serial: 8250/16550 driver $Revision: 1.90 $ 54 ports, IRQ sharing enabled
[4294671.106000] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294671.106000] ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4294671.111000] ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[4294671.112000] ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[4294671.112000] io scheduler noop registered
[4294671.112000] io scheduler anticipatory registered
[4294671.112000] io scheduler deadline registered
[4294671.112000] io scheduler cfq registered
[4294671.113000] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[4294671.114000] EISA: Probing bus 0 at eisa.0
[4294671.114000] EISA: Detected 0 cards.
[4294671.114000] NET: Registered protocol family 2
[4294671.124000] IP: routing cache hash table of 4096 buckets, 32Kbytes
[4294671.124000] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[4294671.124000] TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
[4294671.124000] TCP: Hash tables configured (established 32768 bind 32768)
[4294671.124000] NET: Registered protocol family 8
[4294671.124000] NET: Registered protocol family 20
[4294671.124000] ACPI wakeup devices:
[4294671.124000] PCI0 PCI1 PCI2 UAR1 USB0 USB1 USB2 US20 AC97
[4294671.124000] ACPI: (supports S0 S1 S4 S5)
[4294671.125000] Freeing unused kernel memory: 224k freed
[4294671.532000] vga16fb: initializing
[4294671.532000] vga16fb: mapped to 0xc00a0000
[4294671.646000] Console: switching to colour frame buffer device 80x30
[4294671.646000] fb0: VGA16 VGA frame buffer device
[4294671.907000] input: AT Translated Set 2 keyboard on isa0060/serio0
[4294672.918000] Capability LSM initialized
[4294672.933000] NET: Registered protocol family 1
[4294672.952000] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[4294672.952000] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[4294672.952000] ACPI: bus type ide registered
[4294672.962000] ICH4: IDE controller at PCI slot 0000:00:1f.1
[4294672.962000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[4294672.962000] ICH4: chipset revision 2
[4294672.962000] ICH4: not 100% native mode: will probe irqs later
[4294672.962000] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA
[4294672.962000] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
[4294672.962000] Probing IDE interface ide0...
[4294673.226000] hda: Maxtor 6E040L0, ATA DISK drive
[4294673.481000] hdb: SAMSUNG SV1533D, ATA DISK drive
[4294673.532000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[4294673.532000] Probing IDE interface ide1...
[4294674.204000] hdc: HL-DT-STDVD-ROM GDR8162B, ATAPI CD/DVD-ROM drive
[4294674.918000] hdd: LITE-ON CD-RW SOHR-5238S, ATAPI CD/DVD-ROM drive
[4294674.969000] ide1 at 0x170-0x177,0x376 on irq 15
[4294674.969000] Probing IDE interface ide2...
[4294675.482000] Probing IDE interface ide3...
[4294675.994000] Probing IDE interface ide4...
[4294676.506000] Probing IDE interface ide5...
[4294677.023000] hda: max request size: 128KiB
[4294677.028000] hda: 80293248 sectors (41110 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
[4294677.028000] hda: cache flushes supported
[4294677.028000] /dev/ide/host0/bus0/target0/lun0: p1 p2
[4294677.030000] hdb: max request size: 128KiB
[4294677.030000] hdb: 29897280 sectors (15307 MB) w/472KiB Cache, CHS=29660/16/63, UDMA(33)
[4294677.030000] hdb: cache flushes not supported
[4294677.031000] /dev/ide/host0/bus0/target1/lun0: p1 p2
[4294677.084000] hdc: ATAPI 48X DVD-ROM drive, 256kB Cache
[4294677.084000] Uniform CD-ROM driver Revision: 3.20
[4294677.098000] hdd: ATAPI 52X CD-ROM CD-R/RW drive, 2048kB Cache
[4294677.856000] Attempting manual resume
[4294677.856000] swsusp: Suspend partition has wrong signature?
[4294677.880000] usbcore: registered new driver usbfs
[4294677.880000] usbcore: registered new driver hub
[4294677.881000] USB Universal Host Controller Interface driver v2.2
[4294677.881000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[4294677.881000] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[4294677.881000] uhci_hcd 0000:00:1d.0: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1
[4294677.943000] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[4294677.943000] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000b800
[4294677.943000] hub 1-0:1.0: USB hub found
[4294677.943000] hub 1-0:1.0: 2 ports detected
[4294677.946000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[4294677.946000] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[4294677.946000] uhci_hcd 0000:00:1d.1: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2
[4294678.008000] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[4294678.008000] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b400
[4294678.008000] hub 2-0:1.0: USB hub found
[4294678.008000] hub 2-0:1.0: 2 ports detected
[4294678.011000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[4294678.011000] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[4294678.011000] uhci_hcd 0000:00:1d.2: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3
[4294678.073000] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[4294678.073000] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b000
[4294678.073000] hub 3-0:1.0: USB hub found
[4294678.073000] hub 3-0:1.0: 2 ports detected
[4294678.099000] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
[4294678.099000] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[4294678.099000] ehci_hcd 0000:00:1d.7: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller
[4294678.099000] ehci_hcd 0000:00:1d.7: debug port 1
[4294678.099000] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 4
[4294678.099000] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xc6000000
[4294678.103000] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[4294678.103000] ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
[4294678.103000] hub 4-0:1.0: USB hub found
[4294678.103000] hub 4-0:1.0: 6 ports detected
[4294678.183000] b44.c:v0.95 (Aug 3, 2004)
[4294678.183000] ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 20 (level, low) -> IRQ 20
[4294678.186000] eth0: Broadcom 4400 10/100BaseT Ethernet 00:0c:6e:f3:14:35
[4294678.195000] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004)
[4294678.195000] 8139cp: pci dev 0000:02:0d.0 (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
[4294678.195000] 8139cp: Try the "8139too" driver instead.
[4294678.197000] 8139too Fast Ethernet driver 0.9.27
[4294678.197000] ACPI: PCI Interrupt 0000:02:0d.0[A] -> GSI 21 (level, low) -> IRQ 21
[4294678.197000] eth1: RealTek RTL8139 at 0xa800, 00:50:22:85:80:55, IRQ 21
[4294678.197000] eth1: Identified 8139 chip type 'RTL-8139C'
[4294678.942000] usb 1-2: new full speed USB device using uhci_hcd and address 3[4294679.197000] usb 2-1: new low speed USB device using uhci_hcd and address 2
[4294679.617000] usb 2-2: new low speed USB device using uhci_hcd and address 3
[4294680.245000] usbcore: registered new driver hiddev
[4294680.304000] input: USB HID v1.10 Keyboard [BTC USB Multimedia Keyboard] on usb-0000:00:1d.1-1
[4294680.431000] input,hiddev96: USB HID v1.10 Device [BTC USB Multimedia Keyboard] on usb-0000:00:1d.1-1
[4294680.451000] input: USB HID v1.10 Mouse [USB OpticalWheel Mouse] on usb-0000:00:1d.1-2
[4294680.451000] usbcore: registered new driver usbhid
[4294680.451000] drivers/usb/input/hid-core.c: v2.01:USB HID core driver
[4294681.339000] ACPI: CPU0 (power states: C1[C1])
[4294681.597000] Attempting manual resume
[4294681.607000] swsusp: Suspend partition has wrong signature?
[4294681.619000] kjournald starting. Commit interval 5 seconds
[4294681.619000] EXT3-fs: mounted filesystem with ordered data mode.
[4294682.731000] md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
[4294686.870000] Adding 747012k swap on /dev/hdb1. Priority:-1 extents:1
[4294687.116000] EXT3 FS on hda1, internal journal
[4294693.910000] parport: PnPBIOS parport detected.
[4294693.910000] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
[4294693.996000] lp0: using parport0 (interrupt-driven).
[4294694.044000] mice: PS/2 mouse device common for all mice
[4294697.157000] device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@redhat.com
[4294697.999000] cdrom: open failed.
[4294698.003000] cdrom: open failed.
[4294699.100000] FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[4294699.164000] kjournald starting. Commit interval 5 seconds
[4294699.164000] EXT3 FS on hdb2, internal journal
[4294699.164000] EXT3-fs: mounted filesystem with ordered data mode.
[4294700.971000] Linux agpgart interface v0.101 (c) Dave Jones
[4294700.983000] agpgart: Detected an Intel 845G Chipset.
[4294701.016000] agpgart: AGP aperture is 256M @ 0xe0000000
[4294701.115000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[4294701.122000] shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
[4294701.122000] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
[4294701.472000] shpchp: acpi_shpchprm:\_SB_.PCI0 evaluate _BBN fail=0x5
[4294701.472000] shpchp: acpi_shpchprm:get_device PCI ROOT HID fail=0x5
[4294701.544000] hw_random: RNG not detected
[4294702.099000] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 17
[4294702.099000] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[4294702.453000] AC'97 0 analog subsections not ready
[4294702.513000] intel8x0_measure_ac97_clock: measured 49129 usecs
[4294702.513000] intel8x0: clocking to 48000
[4294705.227000] usbcore: registered new driver snd-usb-audio
[4294706.051000] Real Time Clock Driver v1.12
[4294706.131000] input: PC Speaker
[4294706.287000] Floppy drive(s): fd0 is 1.44M
[4294706.301000] FDC 0 is a post-1991 82077
[4294706.809000] ts: Compaq touchscreen protocol output
[4294709.246000] b44: eth0: Link is down.
[4294711.246000] b44: eth0: Link is up at 100 Mbps, full duplex.
[4294711.246000] b44: eth0: Flow control is on for TX and on for RX.
[4294711.370000] NET: Registered protocol family 10
[4294711.370000] Disabled Privacy Extensions on device c02eb280(lo)
[4294711.372000] IPv6 over IPv4 tunneling driver
[4294712.683000] ACPI: Power Button (FF) [PWRF]
[4294712.683000] ACPI: Power Button (CM) [PWRB]
[4294712.817000] ibm_acpi: ec object not found
[4294719.241000] [drm] Initialized drm 1.0.0 20040925
[4294719.253000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[4294719.255000] [drm] Initialized radeon 1.16.0 20050311 on minor 0: ATI Technologies Inc RV280 [Radeon 9200 PRO]
[4294719.256000] agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
[4294719.256000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
[4294719.256000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[4294719.261000] [drm] Loading R200 Microcode
[4294721.650000] eth0: no IPv6 routers present
[4294721.831000] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[4294721.831000] apm: overridden by ACPI.
[4294723.304000] Bluetooth: Core ver 2.7
[4294723.304000] NET: Registered protocol family 31
[4294723.304000] Bluetooth: HCI device and connection manager initialized
[4294723.304000] Bluetooth: HCI socket layer initialized
[4294723.559000] Bluetooth: L2CAP ver 2.7
[4294723.559000] Bluetooth: L2CAP socket layer initialized
[4294723.596000] Bluetooth: RFCOMM ver 1.5
[4294723.596000] Bluetooth: RFCOMM socket layer initialized
[4294723.596000] Bluetooth: RFCOMM TTY layer initialized
[4295099.646000] Linux video capture interface: v1.00
[4295099.653000] usbcore: registered new driver ov511
[4295099.653000] /home/xerxesis/drivers/ov511-2.31/ov511_core.c: v2.31 : ov511 USB Camera Driver (V4L2 disabled)
[4406043.198000] usbcore: deregistering driver ov511
[4406043.246000] /home/xerxesis/drivers/ov511-2.31/ov511_core.c: driver deregistered
[4406061.522000] Linux video capture interface: v1.00
[4406061.540000] usbcore: registered new driver ov511
[4406061.540000] /home/xerxesis/drivers/ov511-2.31/ov511_core.c: v2.31 : ov511 USB Camera Driver (V4L2 disabled)
alors tu en penses quoi?
je pense avoir fait exactement ce que tu m’as dis donc la il est vrai que je suis un peu pommé la seule chose qui me choque c’est v4l2 qui est desactivé
merci encore pour tout
PS: j’ai encore essayé mais elle n’est toujours pas reconnu ça fait comme si je ne l’avais pas installé ou bien que je n’avais pas installé la bonne
le driver à l’air de se charger correctement mais pas de trouver la webcam 
quand tu la débranches et rebranches, que t’indique dmesg ? (seulement la fin ;))
s’il la reconnais et qu’il l’associe au driver, il devrait te le signaler d’une manière ou d’une autre.
s’il ne l’associe pas au driver, il se contentera de te dire qu’il a trouvé un périphérique usb.
essais de charger à la main v4l et/ou v4l2, on ne sait jamais…
après cela, je suis désolé mais n’ayant pas de webcam moi même et n’en ayant jamais utilisé une, je ne serait pas beaucoup plus t’aider… ce que je t’ai dit juste là sont des généralités valable pour la plupars des périphériques et drivers…
tu peux toujours aller poster ton problème sur le forum officiel ou tu as téléchargé le driver, peut-être qu’il y a une astuce ou une manip à faire à cause d’un bug du driver ou autre…
bah je crois que je me suis trompé de driver est ce que c’est possible il semblerai que ce soit le ov519 possible ou pas
bah c’est possible mais moi j’en sais rien…
quand tu la branches, tu devrais trouver les info utiles grace à dmesg (juste après l’avoir branché dans les dernières lignes), lsusb (liste les périphériques usb trouvés), lspci (liste les périphériques sur le bus pci, mais j’y ai déjà vu des usb, donc tu peux toujours tenter) ou encore lshal (liste les périphériques trouvés par hal, le résultat de la commande est assez compliqué et touffu, mais jettes-y quand même un oeil)
dans tous les cas, essais d’avoir le plus d’infos possibles sur ta webcam et en particulier le nom exact et les numéros de version et révision.
xerxesis@ubuntu:~/ov51x-jpeg-0.5.1$ lsusb
Bus 004 Device 001: ID 0000:0000
Bus 003 Device 001: ID 0000:0000
Bus 002 Device 003: ID 04fc:0013 Sunplus Technology Co., Ltd
Bus 002 Device 002: ID 046d:c310 Logitech, Inc.
Bus 002 Device 001: ID 0000:0000
Bus 001 Device 004: ID 05a9:8519 OmniVision Technologies, Inc.
Bus 001 Device 001: ID 0000:0000
voila exactement ce que j’ai eu je vais recherché un peu plus du coté du forum ubuntu j’ai cru voir un logiciel qui s’appel easycam2 qui pourrais me l’installer tout seul
se serais vraiment bien :ane:
merci encore
sinon voici la fin de mon dmesg
[4294723.596000] Bluetooth: RFCOMM socket layer initialized
[4294723.596000] Bluetooth: RFCOMM TTY layer initialized
[4295099.646000] Linux video capture interface: v1.00
[4295099.653000] usbcore: registered new driver ov511
[4295099.653000] /home/xerxesis/drivers/ov511-2.31/ov511_core.c: v2.31 : ov511 USB Camera Driver (V4L2 disabled)
[4406043.198000] usbcore: deregistering driver ov511
[4406043.246000] /home/xerxesis/drivers/ov511-2.31/ov511_core.c: driver deregistered
[4406061.522000] Linux video capture interface: v1.00
[4406061.540000] usbcore: registered new driver ov511
[4406061.540000] /home/xerxesis/drivers/ov511-2.31/ov511_core.c: v2.31 : ov511 USB Camera Driver (V4L2 disabled)
[4409313.697000] usbcore: deregistering driver ov511
[4409313.737000] /home/xerxesis/drivers/ov511-2.31/ov511_core.c: driver deregistered
[4409473.377000] /home/xerxesis/drivers/ov511-2.31/ovcamchip_core.c: v2.31 : OV camera chip I2C driver
[4409576.898000] Linux video capture interface: v1.00
[4409576.912000] usbcore: registered new driver ov511
[4409576.913000] /home/xerxesis/drivers/ov511-2.31/ov511_core.c: v2.31 : ov511 USB Camera Driver (V4L2 disabled)
[4410531.820000] usbcore: deregistering driver ov511
[4410531.837000] /home/xerxesis/drivers/ov511-2.31/ov511_core.c: driver deregistered
[4410627.161000] Linux video capture interface: v1.00
[4410627.178000] usbcore: registered new driver ov511
[4410627.178000] /home/xerxesis/drivers/ov511-2.31/ov511_core.c: v2.31 : ov511 USB Camera Driver (V4L2 disabled)
[4411637.899000] pwc Philips webcam module version 10.0.6-unofficial loaded.
[4411637.899000] pwc Supports Philips PCA645/646, PCVC675/680/690, PCVC720[40]/730/740/750 & PCVC830/840.
[4411637.899000] pwc Also supports the Askey VC010, various Logitech Quickcams, Samsung MPC-C10 and MPC-C30,
[4411637.899000] pwc the Creative WebCam 5 & Pro Ex, SOTEC Afina Eye and Visionite VCS-UC300 and VCS-UM100.
[4411637.899000] pwc Trace options: 0x00a1
[4411637.901000] usbcore: registered new driver Philips webcam
[4414008.231000] ov51x: no version for "struct_module" found: kernel tainted.
[4414008.231000] ov51x: no version magic, tainting kernel.
[4414008.279000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: USB OV519 video device found
[4414008.648000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Sensor is an OV7648
[4414008.756000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Device at usb-0000:00:1d.0-2 registered to minor 0
[4414008.756000] usbcore: registered new driver ov51x
[4414008.756000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: v1.65-1.11-mark : ov51x USB Camera Driver
[4414009.222000] usbcore: deregistering driver ov51x
[4414009.240000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: driver deregistered
[4414022.677000] ov51x: no version magic, tainting kernel.
[4414022.694000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: USB OV519 video device found
[4414023.050000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Sensor is an OV7648
[4414023.173000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Device at usb-0000:00:1d.0-2 registered to minor 0
[4414023.173000] usbcore: registered new driver ov51x
[4414023.173000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: v1.65-1.11-mark : ov51x USB Camera Driver
[4414033.170000] usbcore: deregistering driver ov51x
[4414033.202000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: driver deregistered
[4414045.622000] ov51x: no version magic, tainting kernel.
[4414045.644000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: USB OV519 video device found
[4414046.001000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Sensor is an OV7648
[4414046.114000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Device at usb-0000:00:1d.0-2 registered to minor 0
[4414046.114000] usbcore: registered new driver ov51x
[4414046.114000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: v1.65-1.11-mark : ov51x USB Camera Driver
[4414071.760000] usbcore: deregistering driver ov51x
[4414071.804000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: driver deregistered
[4414084.206000] ov51x: no version magic, tainting kernel.
[4414084.223000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: USB OV519 video device found
[4414084.577000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Sensor is an OV7648
[4414084.688000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Device at usb-0000:00:1d.0-2 registered to minor 0
[4414084.688000] usbcore: registered new driver ov51x
[4414084.688000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: v1.65-1.11-mark : ov51x USB Camera Driver
[4414387.056000] usbcore: deregistering driver ov51x
[4414387.096000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: driver deregistered
[4414401.178000] ov51x: no version magic, tainting kernel.
[4414401.199000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: USB OV519 video device found
[4414401.558000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Sensor is an OV7648
[4414401.682000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Device at usb-0000:00:1d.0-2 registered to minor 0
[4414401.682000] usbcore: registered new driver ov51x
[4414401.682000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: v1.65-1.11-mark : ov51x USB Camera Driver
[4414755.211000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: No decompressor available
[4414788.033000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: No decompressor available
[4414788.173000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: No decompressor available
[4414888.228000] usb 1-2: USB disconnect, address 3
[4414889.862000] usb 1-1: new full speed USB device using uhci_hcd and address 4
[4414889.957000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: USB OV519 video device found
[4414890.314000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Sensor is an OV7648
[4414890.423000] /home/xerxesis/ov51x-jpeg-0.5.1/ov51x.c: Device at usb-0000:00:1d.0-1 registered to minor 0
c’est bon elle fonctionne grace a un blog tres tres bien expliqué
je le donne pour ceux qui auront le meme probleme
http://azurams.free.fr/index.php/2006/03/0…s=1cordialement
cordialement
XerXeSis
merci beaucoup a toi moi1392 et de tout le tmp que tu ma attribué a travers tes explication c’est vraiment tres généreux
cool
c’est quelle partie qui te manquait pour faire marcher ta webcam (à mon avis le device dans /dev) ? ça pourrait être sympa de le mettre comme ça les personnes qui tombent sur ce topic à cause de problèmes similaires auront un indice
je crois quje n’avais meme pas dépasser la moitier de la page du lien que j’ai donné mais j’ai eu beaucoup de mal a la trouver mais je suis quand meme trop content