impossible de conecte internet j’ai installe rp-pppoe3.7,eagle-usb-2.3.2,usbview ,bien sa marche pas sa fais une semaine que j’essaye de faire marche sa en dehor de sa ma compagnie internet s’est jazztel je vis en espagne quelqun peux ma’ider ?
au secournon, on peut pas t’aider si tu donne pas plus d’infos 
les log de connection ppp ca serais bien déjà , également les messages de syslog
avec eagleusb tu as un script qui s’appelle “startadsl” (en tout cas la dernière fois que je l’ai utilisé… et ça fait quand même quelques temps…) lance le en root et dis nous quel est le résultat.
salut et meci pour le reponse .
alors je 'texplique j’ai installer avec succe enfin je crois rp-pppoe,apres j’install eagle-usb
et a la fin de l’install surprise il me dis qu’il ne reconais pas kernel bref que se n’est pas la bonne version alors j’install kernel-source mais la j’ai un message qui me dis que netcfg est insatisfait d’accors j’ai tous pige tu m’en remetra 2 caisses,ensuite je me prend la tete a conecte j’envoie mais je ne reÇois pas et biansure l’adsl ne marche pas mais je suis conecte puisque j’envoie
http://www.nantes.aeroport.fr/aeroport/htdoc/fr/fret/img/caisses.jpg
blagues a part, essaie de lancer l’install et a la fin, quand il a bien planté, tu tape:
“dmesg”
et
“tail -n 20 /var/log/messages”
les deux vont te retourner des logs, copie les nous ici
rebonjour voila ce que tu m’as demander:
voici ce que tu m’as demande et merci pour ta reponse xingyi
[root@212 ~]# dmesg
Linux version 2.6.12-12mdksmp (apatard@n1.mandriva.com) (gcc version 4.0.1 (4.0.1-5mdk for Mandriva Linux release 2006.0)) #1 SMP Fri Sep 9 17:43:23 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003fff0000 (usable)
BIOS-e820: 000000003fff0000 - 000000003fff3000 (ACPI NVS)
BIOS-e820: 000000003fff3000 - 0000000040000000 (ACPI data)
BIOS-e820: 00000000c0000000 - 00000000d0000000 (reserved)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f5280
On node 0 totalpages: 262128
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 32752 pages, LIFO batch:15
DMI 2.3 present.
ACPI: RSDP (v000 GBT ) @ 0x000f6c60
ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff3040
ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff30c0
ACPI: MCFG (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff6c80
ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x3fff6bc0
ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x00000000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:3 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 15:3 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:80000000)
Built 1 zonelists
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
Kernel command line: auto BOOT_IMAGE=linux root=811 resume=/dev/sdb5 splash=silent
bootsplash: silent mode.
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 3417.880 MHz processor.
Using pmtmr for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 1033444k/1048512k available (2451k kernel code, 14288k reserved, 788k data, 296k init, 131008k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode… Ok.
Calibrating delay loop… 6766.59 BogoMIPS (lpj=3383296)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 0000441d 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal monitoring enabled
Enabling fast FPU save and restore… done.
Enabling unmasked SIMD FPU exception support… done.
Checking ‘hlt’ instruction… OK.
ACPI: Looking for DSDT in initrd… not found.
CPU0: Intel® Pentium® 4 CPU 3.40GHz stepping 04
Enabling SMP…
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay loop… 6815.74 BogoMIPS (lpj=3407872)
CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000
monitor/mwait feature present.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 1024K
CPU: Physical Processor ID: 0
CPU: After all inits, caps: bfebfbff 00000000 00000000 00000080 0000441d 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel P4/Xeon Extended MCE MSRs (12) available
CPU1: Thermal monitoring enabled
CPU1: Intel® Pentium® 4 CPU 3.40GHz stepping 04
Total of 2 processors activated (13582.33 BogoMIPS).
ENABLING IO-APIC IRQs
…TIMER: vector=0x31 pin1=2 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Enabling SMP…
Brought up 2 CPUs
CPU0 attaching sched-domain:
domain 0: span 00000003
groups: 00000001 00000002
domain 1: span 00000003
groups: 00000003
CPU1 attaching sched-domain:
domain 0: span 00000003
groups: 00000002 00000001
domain 1: span 00000003
groups: 00000003
checking if image is initramfs…it isn’t (no cpio magic); looks like an initrd
Freeing initrd memory: 262k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 3.00 entry at 0xfb3b0, last bus=4
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:00.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\SB.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\SB.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\SB.PCI0.PEX2._PRT]
ACPI: PCI Interrupt Routing Table [\SB.PCI0.HUB0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
Linux Plug and Play Support v0.97 © Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
PCI: If a device doesn’t work, try “pci=routeirq”. If it helps, post a report
pnp: 00:0b: ioport range 0x400-0x4bf could not be reserved
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac)
apm: disabled - APM is not SMP safe.
audit: initializing netlink socket (disabled)
audit(1140887935.228:0): initialized
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:01.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1c.2 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
vesafb: framebuffer at 0xd0000000, mapped to 0xf8880000, using 3750k, total 262144k
vesafb: mode is 800x600x16, linelength=1600, pages=2
vesafb: protected mode interface info at c000:d2a0
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
bootsplash 3.1.6-2004/03/31: looking for picture…<6> silentjpeg size 27015 bytes,<6>…found (800x600, 26967 bytes, v3).
Console: switching to colour frame buffer device 93x30
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards…
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH6: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
ICH6: chipset revision 3
ICH6: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0…
hda: HL-DT-ST DVDRAM GSA-4160B, ATAPI CD/DVD-ROM drive
hdb: HL-DT-STDVD-ROM GDR8163B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1…
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP established hash table entries: 262144 (order: 9, 2097152 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 1
Starting balanced_irq
ACPI wakeup devices:
PCI0 PEX0 PEX1 PEX2 PEX3 HUB0 USB0 USB1 USB2 USB3 USBE AC97 MC97 AZAL
ACPI: (supports S0 S1 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 3 devices found
devfs_mk_dev: could not append to parent for md/0
md: Autodetecting RAID arrays.
md: autorun …
md: … autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
SCSI subsystem initialized
libata version 1.11 loaded.
input: AT Translated Set 2 keyboard on isa0060/serio0
ata_piix version 1.03
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xD000 ctl 0xD402 bmdma 0xE000 irq 19
ata2: SATA max UDMA/133 cmd 0xD800 ctl 0xDC02 bmdma 0xE008 irq 19
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3468 86:3c01 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 234441648 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
logips2pp: Detected unknown logitech mouse model 85
input: ImPS/2 Logitech Wheel Mouse on isa0060/serio1
ata2: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4003 85:3468 86:3c01 87:4003 88:207f
ata2: dev 0 ATA, max UDMA/133, 312579695 sectors: lba48
ata2: dev 0 configured for UDMA/133
scsi1 : ata_piix
Vendor: ATA Model: ST3120827AS Rev: 3.42
Type: Direct-Access ANSI SCSI revision: 05
Vendor: ATA Model: ST3160023AS Rev: 3.18
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 234441648 512-byte hdwr sectors (120034 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sdb: 312579695 512-byte hdwr sectors (160041 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 312579695 512-byte hdwr sectors (160041 MB)
SCSI device sdb: drive cache: write back
/dev/scsi/host1/bus0/target0/lun0: p1 p2 < p5 p6 >
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 296k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000bc00
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000b000
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000b400
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000b800
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-2: new full speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf0204000
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
ts: Compaq touchscreen protocol output
usb 5-4: new high speed USB device using ehci_hcd and address 2
usb 5-5: new high speed USB device using ehci_hcd and address 3
Initializing USB Mass Storage driver…
usb 5-8: new high speed USB device using ehci_hcd and address 6
hub 5-8:1.0: USB hub found
hub 5-8:1.0: 4 ports detected
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
scsi3 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
EXT3 FS on sdb1, internal journal
usb 3-2: new low speed USB device using uhci_hcd and address 2
Adding 1124508k swap on /dev/sdb5. Priority:-1 extents:1
usb 2-2: USB disconnect, address 2
usbcore: registered new driver xpad
drivers/usb/input/xpad-core.c: driver for Xbox controllers with mouse emulation v0.1.4
Linux agpgart interface v0.101 © Dave Jones
nvidia: module license ‘NVIDIA’ taints kernel.
ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:01:00.0 to 64
NVRM: loading NVIDIA Linux x86 NVIDIA Kernel Module 1.0-7676 Fri Jul 29 12:58:54 PDT 2005
usb 4-1: new full speed USB device using uhci_hcd and address 2
hw_random: RNG not detected
agpgart: Detected an Intel 915G Chipset.
agpgart: AGP aperture is 256M @ 0x0
kjournald starting. Commit interval 5 seconds
EXT3 FS on sdb6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Supermount version 2.0.4 for kernel 2.6
ntfs: Ignoring new-style parameters in presence of obsolete ones
NTFS driver 2.1.22 [Flags: R/O DEBUG MODULE].
usbcore: registered new driver hiddev
[eagle-usb] driver V2.2.0 loaded
NTFS volume version 3.1.
usb 5-8.1: new full speed USB device using ehci_hcd and address 7
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 7
usb-storage: waiting for device to settle before scanning
usb 5-8.4: new full speed USB device using ehci_hcd and address 8
input: USB HID v1.00 Joystick [Saitek Saitek R220] on usb-0000:00:1d.2-2
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
[eagle-usb] New USB ADSL device detected, waiting for DSP code…
[eagle-usb] Interface 0 accepted.
[eagle-usb] created proc entry at : /proc/driver/eagle-usb/004-002
usbcore: registered new driver eagle-usb
drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 7 if 0 alt 0 proto 2 vid 0x04F9 pid 0x0169
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[eagle-usb] ioctl EU_IO_CMVS received and treated.
loop: loaded (max 8 devices)
[eagle-usb] ioctl EU_IO_OPTIONS received
[eagle-usb] ioctl EU_IO_DSP received
[eagle-usb] Loading DSP code to device…
[eagle-usb] DSP code successfully loaded to device
hda: ATAPI 40X DVD-ROM DVD-R-RAM CD-R/RW drive, 2048kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
hdb: ATAPI 52X DVD-ROM drive, 256kB Cache, UDMA(33)
Vendor: 256MB Model: USB2.0FlashDrive Rev: A4
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sdc: 512000 512-byte hdwr sectors (262 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 00 00 00
sdc: assuming drive cache: write through
SCSI device sdc: 512000 512-byte hdwr sectors (262 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 00 00 00
sdc: assuming drive cache: write through
/dev/scsi/host3/bus0/target0/lun0: p1
ioctl_internal_command: <3 0 0 0> return code = 8000002
: Current: sense key: No Sense
Additional sense: No additional sense information
Attached scsi removable disk sdc at scsi3, channel 0, id 0, lun 0
usb-storage: device scan complete
Vendor: Brother Model: DCP-110C Rev: 1.00
Type: Direct-Access ANSI SCSI revision: 02
Attached scsi removable disk sdd at scsi4, channel 0, id 0, lun 0
usb-storage: device scan complete
[eagle-usb] Modem operational !!
[eagle-usb] Ethernet device eth1 created.
bootsplash 3.1.6-2004/03/31: looking for picture…<6> silentjpeg size 27015 bytes,<6>…found (800x600, 26967 bytes, v3).
bootsplash: status on console 0 changed to on
ip_conntrack version 2.1 (8191 buckets, 65528 max) - 260 bytes per conntrack
ip_tables: © 2000-2002 Netfilter core team
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports 2 throttling states)
ACPI: Processor [CPU1] (supports 2 throttling states)
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
NET: Registered protocol family 17
tg3.c:v3.31 (June 8, 2005)
ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:03:00.0 to 64
eth0: Tigon3 [partno(BCM95751) rev 4001 PHY(5750)] (PCIX:100MHz:32-bit) 10/100/1000BaseT Ethernet 00:0f:ea:3f:4c:c0
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
eth0: dma_rwctrl[76180000]
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE]
lp0: using parport0 (interrupt-driven).
lp0: console ready
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1b.0 to 64
usbcore: registered new driver snd-usb-audio
NET: Registered protocol family 10
Disabled Privacy Extensions on device c03efce0(lo)
IPv6 over IPv4 tunneling driver
Installing knfsd (copyright © 1996 okir@monad.swb.de).
ioctl_internal_command: <3 0 0 0> return code = 8000002
: Current: sense key: No Sense
Additional sense: No additional sense information
ioctl_internal_command: <3 0 0 0> return code = 8000002
: Current: sense key: No Sense
Additional sense: No additional sense information
ioctl_internal_command: <3 0 0 0> return code = 8000002
: Current: sense key: No Sense
Additional sense: No additional sense information
ioctl_internal_command: <3 0 0 0> return code = 8000002
: Current: sense key: No Sense
Additional sense: No additional sense information
ioctl_internal_command: <3 0 0 0> return code = 8000002
: Current: sense key: No Sense
Additional sense: No additional sense information
ioctl_internal_command: <3 0 0 0> return code = 8000002
: Current: sense key: No Sense
Additional sense: No additional sense information
ioctl_internal_command: <3 0 0 0> return code = 8000002
: Current: sense key: No Sense
Additional sense: No additional sense information
ioctl_internal_command: <3 0 0 0> return code = 8000002
: Current: sense key: No Sense
Additional sense: No additional sense information
ioctl_internal_command: <3 0 0 0> return code = 8000002
: Current: sense key: No Sense
Additional sense: No additional sense information
eth1: no IPv6 routers present
eth0: no IPv6 routers present
bootsplash 3.1.6-2004/03/31: looking for picture…<6>…found (800x600, 9887 bytes, v3).
bootsplash: status on console 0 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture…<6>…found (800x600, 9887 bytes, v3).
bootsplash: status on console 1 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture…<6>…found (800x600, 9887 bytes, v3).
bootsplash: status on console 2 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture…<6>…found (800x600, 9887 bytes, v3).
bootsplash: status on console 3 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture…<6>…found (800x600, 9887 bytes, v3).
bootsplash: status on console 4 changed to on
bootsplash 3.1.6-2004/03/31: looking for picture…<6>…found (800x600, 9887 bytes, v3).
bootsplash: status on console 5 changed to on
CSLIP: code copyright 1989 Regents of the University of California
PPP generic driver version 2.4.2
[root@212 ~]# tail -n 20/var/log/messages
tail: 20/var/log/messages: el número de líneas no es válido
[root@212 ~]# tail -n 20 /var/log/messages
Feb 25 17:22:14 212 pppd[6468]: invalid numeric parameter ‘yes’ for idle option
Feb 25 17:22:14 212 pppoe-connect: PPPoE connection lost; attempting re-connection.
Feb 25 17:22:14 212 pppd[6470]: invalid numeric parameter ‘yes’ for idle option
Feb 25 17:22:14 212 adsl-connect: ADSL connection lost; attempting re-connection.
Feb 25 17:22:19 212 pppd[6474]: invalid numeric parameter ‘yes’ for idle option
Feb 25 17:22:19 212 pppoe-connect: PPPoE connection lost; attempting re-connection.
Feb 25 17:22:19 212 pppd[6476]: invalid numeric parameter ‘yes’ for idle option
Feb 25 17:22:19 212 adsl-connect: ADSL connection lost; attempting re-connection.
Feb 25 17:22:24 212 pppd[6480]: invalid numeric parameter ‘yes’ for idle option
Feb 25 17:22:24 212 pppoe-connect: PPPoE connection lost; attempting re-connection.
Feb 25 17:22:24 212 pppd[6482]: invalid numeric parameter ‘yes’ for idle option
Feb 25 17:22:24 212 adsl-connect: ADSL connection lost; attempting re-connection.
Feb 25 17:22:29 212 pppd[6486]: invalid numeric parameter ‘yes’ for idle option
Feb 25 17:22:29 212 pppoe-connect: PPPoE connection lost; attempting re-connection.
Feb 25 17:22:29 212 pppd[6488]: invalid numeric parameter ‘yes’ for idle option
Feb 25 17:22:29 212 adsl-connect: ADSL connection lost; attempting re-connection.
Feb 25 17:22:34 212 pppd[6492]: invalid numeric parameter ‘yes’ for idle option
Feb 25 17:22:34 212 pppoe-connect: PPPoE connection lost; attempting re-connection.
Feb 25 17:22:34 212 pppd[6494]: invalid numeric parameter ‘yes’ for idle option
Feb 25 17:22:34 212 adsl-connect: ADSL connection lost; attempting re-connection.
[root@212 ~]#
ta un pb dans ton fichier de conf 
regarde l’option ‘idle’, d’aprés le fichier de log ca vient de ca
tu veux dire que je regarde a travers le terminal root idle s’est sa que tu veux dire
je tape idle et je te copie se qui se passe a tous de suite
bien voila se qui appatait:
python2.4.1(#2aug 25 2005, 18:20:57)[gcc4.0.1(4.0.1-2 mdk for mandriva linux release 2006,0]on linux 2 type "copirygth " "credits" or licence()
for more information
personal firewalle software may warn about connection idle.
make to its subprocess using comput’s internel loopback interface.this connection is not visible on any external interface and no data is sent to or releived from the internet.
voila s’est ce qui m’apparait une fois taper la comande que tu m’as donne come root.
ensuite j’ai essaye d’installe netcfg et le message est (du a la non satisfaction de la permissionne peu s’installe)
non non non
lit bien la ligne :
le paramétre que tu a rentré pour l’option “idle” est invalide, donc il faut que tu regarde dans un fichier de configuration ou se trouve l’option “idle” et que tu regarde pourquoi le paramétre de cette option bug
désolé mais je peut pas plus t’aider, ca fait une eternité que j’utilise plus eagleusb